Power inductors COILMX MS0630-8R2M designed for operation in battery powered and electronic devices

Product Overview

The MS0630 is a series of low-profile, high-current power inductors designed for a variety of electronic applications. These inductors are suitable for battery-powered devices, DC/DC converters in distributed power systems, and DC/DC converters for field-programmable gate arrays. They offer robust performance with a wide operating temperature range and are built to meet demanding power supply requirements.

Product Attributes

• Brand: MOTTOTECHNOLOGY
• Series: MS0630
• Origin: SHENZHEN
• Material: Not specified
• Color: Not specified
• Certifications: Not specified

Technical Specifications

General Specifications:

Notes:

• All test data is referenced to 25 ambient.
• Irms: DC current (A) that will cause an approximate T of 40.
• Isat: DC current (A) that will cause L0 to drop approximately 30%.
• Operating temperature range: -55 to +125.
• The part temperature (ambient + temp rise) should not exceed 125 under worst-case operating conditions. Circuit design, component, PWB trace size and thickness, airflow and other cooling precision all affect the part temperature. Part temperature should be verified in the end application.
• The rated current as listed is either the saturation current or the heating current depending on which value is lower.

Outline Dimensions (mm): Not specified in detail, refer to procurement specification sheet.

Applications:

• Low profile, high current power supplies.
• Battery powered devices.
• DC/DC converters in distributed power systems.
• DC/DC converters for field programmable gate array.

Contact Information:

• Website: Http://www.coilmx.com
• Email: sales@mottotech.com

Important Usage Notes:

• Please obtain the procurement specification sheet for detailed characteristics and specifications.
• Content may change without prior notice due to product improvements.
• Storage time is within 6 months, under storage conditions (temperature 5-40C, humidity below 10-75%RH).
• Terminal electrode solderability may degrade if storage time is exceeded.
• Do not use or store in a gas corrosive environment (salt, acid, alkali, etc.).
• Preheating is required before soldering.
• The temperature difference between preheating temperature, soldering temperature, and chip temperature should be within 150C.
• Post-installation soldering correction should be within the conditions specified in the specification sheet.
• Overheating may cause short circuits, performance degradation, or reduced lifespan.
• When assembling the printed circuit board with the chip into the device, be careful not to apply residual stress to the chip due to overall deformation of the printed circuit or local deformation such as fastening parts.
• The device generates heat (temperature rise) when powered on, so sufficient margin should be left in the thermal design.
• For magnetic shielded types, pay attention to coil placement during substrate design.
• Electromagnetic interference may cause malfunction.
• Use an anti-static wrist strap as static electricity from the human body can be transferred to the ground wire.
• Do not place the product near magnets or magnetic objects.
• Use within the range specified in the procurement specification sheet.

Disclaimer:

• This product catalog describes products for general electronic equipment (AV equipment, communication equipment, home appliances, entertainment equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) used in general standard applications under normal operation and usage methods.
• The company does not guarantee applicability, performance, quality, etc., for the following uses (hereinafter referred to as 'Specific Uses') that require high safety and reliability, or where equipment failure, malfunction, or poor operation may cause damage to life, body, or property, or may have significant social impact: (1) Aviation, aerospace equipment; (2) Transportation equipment (automobiles, trains, ships, etc.); (3) Medical equipment; (4) Power generation control equipment; (5) Nuclear power related equipment; (6) Submarine equipment; (7) Vehicle control equipment; (8) Public high-level information processing equipment; (9) Military equipment; (10) Electric heating appliances, combustion equipment; (11) Disaster prevention and anti-theft equipment; (12) Various safety devices; (13) Other uses identified as Specific Uses.
• Customers intending to use this product outside the scope, conditions of this product catalog, or in Specific Uses should consult with the relevant department of the company in advance. The company will negotiate usage purposes different from those described in this product catalog in accordance with customer requirements.
• When designing equipment that uses products described in this product catalog, ensure that protective circuits and devices, as well as backup circuits, are installed to comply with the intended use and state of the equipment.

Power inductors COILMX MS0630-8R2M designed for operation in battery powered and electronic devices Images